Step-by-step instructions for replacing shock absorbers on a Samsung washing machine

Automatic washing machines Samsung have a complex device. The overall effect of washing and comfort when using washing equipment depends on how well each of the parts works.

In some cases, usually after many years of service, the elements of the apparatus begin to wear out. Some of them can be repaired, others, such as shock absorbers, can only be replaced.

We will tell you how to replace shock absorbers on a Samsung washing machine in the article.

What do the details look like?

The purpose of the shock absorbers is to damp the vibrations of the automatic machine during the washing process. When the drum is turned violently, the washing machine vibrates. The shock absorbers located in the lower part prevent it from bouncing and twitching.

The device of these parts includes the following elements:

• cylinder;
• gaskets;
• piston with shutters;
• spring.

In modern models, spring dampers are replaced by dampers, which have a similar cylindrical design, but no springs.

The dampers are also located under the tank, and the springs are above it, it is on them that the tank itself is suspended... Such designs are considered more relevant, as they contribute to a better performance of the main function - vibration damping.

Depending on the model of the washing machine and user settings, the drum can rotate up to 1,800 rpm. This creates a significant load, which contributes to the wear of the parts and connections involved in this process.

Shock-absorbing devices, making springy movements, allow the drum to rotate... And at the same time, the increased load is not transferred to the adjacent nodes, which, thanks to this, serve much longer.

How do you know if you need to change them?

Damage to shock absorbers and dampers for housewives does not go unnoticed. Malfunctions of this unit always declare themselves with noise and knocking uncharacteristic for normal operation.

In addition, the following manifestations can be considered indirect signs of wear:

• strong vibration and even spontaneous movement of the washing machine on the floor during washing and spinning;
• an abnormally weak spin or its complete absence is possible.

Since the listed symptoms are characteristic of other malfunctions, the type of the hatch cuff and the condition of the tank should also be analyzed. In case of serious problems with the shock absorbers, the tank begins to sag and lose its elasticity.

This circumstance may even have external manifestations:

• creases and folds on the hatch seal;
• lowering the drum below the normal level;
• lack of elasticity of its attachment.

On top-loading machines, in the event of a malfunction, you may notice that the tank can swing freely if touched by hand. The same circumstance can be seen in front-loading machines with the top cover removed.

Such manifestations can occur even with an empty drum, and under load, the situation is further aggravated. If there is no damage, then the tank, after swinging it by hand, very quickly returns to its original position without unnecessary swinging.

If the seal is crushed on only one side, it is likely that only one damper has failed.

If there is a problem with the shock absorbers, they must be replaced immediately. In a faulty condition, the machine cannot be operated, as this can lead to breakdowns of other parts and, as a result, more complex and more expensive repairs.

Procedure

With use, the resistance between the piston and the cylinder decreases and the damping function becomes weaker.

Trying to repair them is not worth it - no spare parts are available for them, and home-grown measures will have a too short-term effect, so these parts should be replaced with new ones when worn.

Damping devices of washing machines perform purely mechanical work, and are not connected to the electrical circuit of the machine. This makes it possible to replace them even without special knowledge of electrical engineering. But to get access to these parts, the washing machine will have to be partially disassembled.

Procedure:

1. If there is water in the washing machine, it must be drained. Residual water - drain through the drain filter.
2. Laundry - remove from drum.
3. Disconnect the machine from the network.
4. Shut off the water supply.
5. Pull the device out so that it is easily accessible from all sides.
6. Remove the top cover by unscrewing the screws that secure it from the back.
7. Remove the powder tray.
8. Unscrew all screws that secure the control panel. Place the removed part on top of the machine so as not to break the contacts.
9. Remove the collar from the front of the washing machine. It is secured with a spring wire clamp, which must be pry off with a screwdriver and removed.
10. The cuff is tucked into the inside of the machine, into the drum.
11. Remove the front panel by unscrewing all screws holding it. Disconnect the wires from the door lock.
12. The dampers that need to be replaced are located under the tank, on both sides.
13. Unscrew the fasteners with a wrench and remove the dampers.
14. Install new parts in their place. Tighten the fasteners carefully.
15. Assemble the washing machine in reverse order
16. After assembly, connect all communications.
17. Carry out a test run of work, for example, a quick wash with a spin.

Another way to access the dampers is through the bottom... In this case, the machine (with all the water previously drained) is installed at an angle. If there is a panel on the bottom side, remove it. Dampers are replaced in the same way.

The process of replacing shock absorbers on a washing machine - in the video:

Parts selection rules

Each model of the washing machine has its own design features. Therefore, there are no universal spare parts that fit all washers.

When buying new shock absorbers, it is advisable to make sure of their quality. When squeezed, the part must resist.

If, when compressing, practically no effort is required, such a part is not suitable for installation.

You should not buy more powerful shock absorbers in the hope that the washing machine can be overloaded. This is an erroneous opinion, this cannot be done, since all elements of the machine (and not only dampers) are designed for certain loading parameters specified by the manufacturer.

If you have doubts about choosing a new pair of parts, you can go to the store with the removed ones and ask the seller to pick up similar ones.

Video review on the selection of shock absorbers:

Master call: repair price and ordering

If it is impossible to replace shock absorbers on your own, it is better to call a master from a company that provides repairs to washing household appliances. When leaving an application, it is necessary to inform the dispatcher about the model of the automatic machine, this information is in the passport for the product. If dampers have already been purchased, then this should also be mentioned.

The duration of the work of the master on average - up to 1.5 hours, if along the way no problems were found that also require the attention of a specialist. Upon completion of the work, a test run of the machine is made and a guarantee for the repair is issued.

It is not advisable to call the masters for random ads, as there is a risk of getting caught by scammers. At the same time, you may not get a quality repair at all. It is better to contact a trustworthy company that has been on the service market for several days.

Learn more about Samsung washing machine repair in this section.

Conclusion

Replacing shock absorbers on a Samsung washing machine can be done independently, or by using the services of a home appliance repair company. If you are not confident in your ability to replace parts yourself, it is better to entrust the work to a professional.