What is the reason that the Samsung washing machine does not collect water, how to fix the problem?

Any previously operated automatic washing machine (CMA) may refuse to draw water. This problem is no exception for Samsung technology.

The reasons that led to the termination of the program may be different. To eliminate them, it is necessary to carry out diagnostics. It is on its results that further steps to eliminate the malfunction will depend.

What is the reason that the Samsung washing machine does not collect water, how to fix the problem, we will tell in the article.

Why is there no water for washing?

There are situations when the automatic machine does not collect water, but it does not have any visible and hidden defects. The cause of the failure may lie in the operation of the main pipeline through which water enters the tank.

This group of reasons includes:

• temporary interruptions in water supply in the house or entrance;
• closed valve on the pipe supplied to the device;
• kinking of the rubber hose through which the incoming water flows.

Possible causes include:

1. Inlet valve defective. An additional sign of this defect may be incomplete rinsing of powder from the tray compartment.
2. Clogged inlet mesh. The problem grows gradually, first expressed in a slow flow of water into the tank.
3. Clogging of the perforations of the filter, which is responsible for the rough cleaning of the water entering the machine.
4. Defective water level sensor. It occurs due to particles of fibers or other contaminants getting into the pressure switch wire.
5. Breakdown of the control board. Failure of resistors can be a special case of this problem.
6. Leakage of the hose connecting the water level sensor and the washing machine tank.
7. Broken lock on the hatch. If the door latches but the electronic interlock fails, the machine will not start.

If the washing machine has a display, a certain code will be reflected on it. The error that appears helps to determine the reason for stopping the program.

What to do?

Some of the problems you can fix yourself... If hitching with external elements (valve, water supply, door) are excluded from the list of possible reasons, proceed directly to the repair of the AGR. The method of restoring the equipment to work depends on the nature of the breakdown.

Cleaning the mesh filter

This part is located in the inlet hose. To clean it, you need to perform several sequential steps:

• close the flow valve on the incoming water pipe;
• unscrew the inlet hose from the washing machine;
• using pliers, remove the mesh from the valve;
• rinse the filter element under running water;
• put the mesh back in place and connect the hose.

Repairing the pressure switch

If it is found that water does not enter the tank due to problems with the water level sensor, it is dismantled.

To do this, perform three actions:

1. Remove the cover of the machine.
2. Unscrew the mounting bolts.
3. Disconnect the hose and wires.

If the pressure switch burns out, then you need to buy exactly the same model. The new sensor is installed in place, the hose and contacts are connected. The last step is to tighten the fixing bolts.

Solving the problem with blocking the hatch

To fix this problem, it is recommended to contact a specialist... But if you have the necessary components and skills, you can make the repair yourself.

If the door is skewed due to strong vibration of the CMA during spinning, then it is enough to tighten the fasteners or replace the hinges.

If checking the electronic lock with a multimeter showed that the problem lies precisely in this part, then they begin to replace it. The castle is dismantled and a new copy is installed in its place.

Replacing the water supply valve

When this important electronic part burns out, it must be replaced. The procedure can be done independently.

The water supply valve replacement algorithm includes several steps:

1. The device is disconnected from the power supply, the water supply from the water supply is cut off.
2. Disconnect the hoses from the valves located at the top of the rear panel.
3. The liquid remaining inside the hoses is drained.
4. After unscrewing the connecting bolts, remove the cover of the washing machine.
5. Take pictures of the location of the wires going to the valve.
6. Retaining fasteners are removed from each of the four hoses.
7. By unscrewing the screw, they take out the broken water supply valve.
8. A new valve is installed in its place, fixed with a bolt.
9. Connect all previously removed hoses.
10. Restore the wiring, guided by the photographed diagram.
11. Replace the housing cover and connect the inlet hose.

Repair or replacement of the control board

If the "silence" of the machine is the result of a banal malfunction of the control module, then it is enough to restart the device. To do this, it is disconnected from the power supply for 10-15 minutes. This time is enough for the system to restore operation.

Broken control board is a more serious problem. The defective module is removed and replaced with a new one, or a partial repair is made.

Dismantling is carried out as follows:

• remove the cover of the washing machine;
• take out the powder receptacle;
• disconnect the dashboard fasteners;
• remove the control module clips.

If it is enough to restore the contacts for repair, then use a special liquid to clean them. When certain paths or connections are closed, they are re-soldered. If repair is not possible, the board is replaced with a new one.

Master call

Many users find it difficult to independently understand the device and repair Samsung... To solve the problem, it is advisable to invite a specialist. He will carry out a complete diagnosis of the device and identify the real cause of the problem.

Home repairs often turn into the need for repeated intervention in the design of the washing machine. This is fraught with additional cash costs.

The repair technology has been worked out in such workshops to the smallest detail. Craftsmen use proven tools and high-quality components. The cost of repairing a Samsung in case of a tank filling problem depends on the cause of the breakdown.

Workshop prices include the following rates:

• replacement of the water supply valve - from 1100 rubles;
• flashing or replacing the control board - from 1,500 rubles;
• replacement of the water level sensor - from 1300 rubles;
• reinstalling the door lock - from 1,500 rubles.

You can also find someone who does a private home repair of washing machines. However, contacting such ads sometimes ends up with new problems.

Private craftsmen do not give a documented guarantee for their work and often overcharge... A verbal agreement may end not in favor of the owner of the equipment. Therefore, contacting official workshops is more profitable both from a technical and economic point of view.

How to avoid problems with Samsung clipper in the future?

To forget about the problem with water intake for a long time or forever, you need to remember about provoking factors. It is important not to allow them when using the Samsung washing machine.

A problem can be caused by:

1. High humidity in the room where the appliance is installed. This leads to dampness and breakdown of contacts. The room must have good ventilation and be heated.
2. Sudden changes in voltage. Such electrical failures can burn the board. For protection, it is recommended to install special modular-type voltage relays in the house or connect the SMA through a stabilizer.
3. Worn out power cord, plug or socket. Ensure that the equipment that supplies power to the washing machine is always in good working order.

Related videos

Why the washing machine does not collect water and how to fix it, the video will tell you:

Conclusion

The refusal of the Samsung washing machine to draw water is not a reason to buy a new unit. Some reasons can be easily eliminated on their own or with the help of a specialist. The volume, time and cost of repairs are individual in each case. These issues are resolved after diagnosis.