Why does the e9 error appear on the display of the Samsung washing machine, how to fix it?

foto23365-1Samsung washing machines are distinguished by thoughtful functionality. If something goes wrong in the equipment, it signals this with a special code that appears on the screen.

One of these alphanumeric values ​​is the E9 error. Read about what the E9 error code of the Samsung washing machine means and how to deal with it in the article.

What does the code mean?

foto23365-2Error E9 indicates that a leak has occurred, or the tank has drained water on its own. Depending on the model of your washing machine, this the code can be designated as follows:

  • LE;
  • LC;
  • LE1.

If the device is not equipped with a screen, then specific LED signals will indicate a leak, namely: the BIO 60 temperature indicators and cold wash will light up, the buttons for all modes will flash in parallel.

Decoding

The e9 error appears if the water level sensor detects a drop in the drum 4 times in a row for several minutes. Therefore, so often users find a puddle of soap on the floor.

The code can appear both in a few seconds after the start of the cycle, and in a few minutes from its beginning, after the machine has collected and drained the water several times.

However, the E9 error does not always indicate a leak. Failure of some parts can lead to its appearance. It also happens that the code is the result of minor problems that you can fix on your own.

Reasons for the appearance

Among the possible reasons for the appearance E9 errors are distinguished:

  1. Incorrect hose connection. If he does not make the upper loop, then the water will go into the sewer by gravity. First, the device will draw and drain water, after which a typical error will appear on the screen.
  2. There is a blockage in the area of ​​the powder tray. It can become clogged with detergent residues and cause water to flow onto the floor.
  3. foto23365-3Poor quality powder or hand wash is used.
  4. The "aquastop" sensor is out of order.
  5. The pressure switch was damaged.
  6. The pipe located near the washing machine tank is damaged. A sharp object, such as a nail, needle or pin, can become the cause of the violation of its integrity.
  7. Shorted the wires inside the system, or they were broken.
  8. The cuff is damaged, most often this occurs due to accidental ingestion of solid debris into the drum. Sometimes it dries out, loses its elasticity and leaks due to prolonged use.
  9. The electronic module responsible for the functioning of the washing machine is out of order.

Some errors can be corrected by yourself, to eliminate other problems you will need the help of a specialist.

How to fix it on your own?

Some problems leading to the appearance of the e9 error can be corrected by yourself, but first you need to find out the cause. Self-diagnosis is carried out as follows:

  • inspect the hose for damage;
  • assess whether the hose is correctly connected to the sewer;
  • inspect the filters and the correctness of their installation;
  • check the detergent tray, if it is clogged, remove it and wash it;
  • inspect the cuff for a violation of its integrity;
  • check all pipes;
  • inspect wires and terminals.

When the cause is found out, you can begin to eliminate it.

Replacing the Aquastop sensor

The most common reason for the e9 error is the breakdown of the Aquastop sensor, which is located in the pallet. To replace it, take the following actions:

  1. foto23365-4Remove all fasteners from the pallet.
  2. Remove it.
  3. Disconnect the wires, disconnect the latches and remove the sensor.
  4. Attach a new part in the same way.
  5. Assemble the washing machine.

The cost of the sensor is about 1000 rubles.

Failure of the pressure switch

Another reason for the e9 error is the failure of the pressure switch (water level sensor). It is easy to replace it yourselfif you follow the following sequence of actions:

  • unscrew the bolts that are responsible for securing the cover to the machine, remove it;
  • disconnect the sensor by disconnecting the wires;
  • unclench the clamp and remove the tube;
  • install a new part, assemble a washing machine.

The price of a new pressure switch for a Samsung washing machine is 1,300 rubles.

When disassembling the washing machine yourself, you need to remember the procedure. This will allow you to properly assemble the device.

Damaged cuffs and pipes

foto23365-5If the cuff is damaged or has lost elasticity, it must be replaced.... It is difficult to cope with this task on your own.

First you need to remove the upper clamp, then dismantle the rubber band and the inner clamp.

To get to the door cuff, you will need to remove the front panel of the washing machine. If possible, it is better to entrust this difficult work to a specialist. Incorrect operation can damage the body and cover of the machine.

If the branch pipe is out of order, then you can access it through the bottom... In addition to the part itself, you will need to purchase new fasteners. It cannot be used again.

If you are not sure that it will be possible to replace the part on your own without loss, it is better to contact a specialist.

When should you call the master?

Only a master can cope with some breakdowns. Without professional knowledge and a specialized tool, it will be difficult to do it yourself.

Depending on the complexity of the work, from the chosen workshop and from the locality, the price may differ. However, there shouldn't be a significant difference. You can try to save money by contacting a private master.

To minimize the risk of meeting scammers, it is necessary to study the reviews of the selected specialist. You need to inquire about the cost of repair work before agreeing to carry it out.

Services and their cost:

  1. Replacing the cuff... Signs of breakdown: error E9 appears, there may be no water on the floor, but the pan will be full. If a complete replacement of the gum is required, the cost of the work will be 1900 rubles. When the damage is minor, the cuff can be turned upside down and sealed. Additionally, you will need to pay the cost of the seal itself.
  2. foto23365-6Replacing the nozzle... Signs of breakdown: the machine gives an error, water appears in the pallet and on the floor. The cost of work is 1800 rubles.
  3. Replacing the pressure switch... Signs: error E9 appears, the machine does not start washing. The cost of replacing the sensor is 1900 rubles.
  4. Replacing the electronic control module... Signs: a breakdown can appear at any time, the machine either completely breaks down or gives an error. Replacement or repair of the electrical circuit is required. The minimum cost of work is 2400 rubles.
  5. Replacing the Aquastop sensor... Breakdown signs: no water, an error appears. Cost of work - 2400 rubles
  6. Replacing the drain hose... Symptoms: a leak appears at the back of the washing machine, a code is displayed on the screen. The cost of replacing the hose: 1400 rubles.
  7. Replacing the wiring... Signs: the code appears on the screen and disappears. Service cost: from 1800 rubles.

Problem prevention

Prevent error E9 the following recommendations will help:

  • to prevent damage to the cuff or drain hose, you need to carefully check the pockets before washing, remove all sharp objects from them;
  • for washing things, you can use a powder labeled "Automatic", a detergent marked "hand wash" is not suitable;
  • the powder tray must be regularly removed and cleaned;
  • in a private house, you need to take care of the absence of rodents - they often spoil the wires by gnawing them;
  • if the apartment regularly knocks out plugs, you need to call an electrician to fix the problem.

Advice

Information that will be useful to all owners of Samsung brand washing machines:

  1. foto23365-7The e9 code appears on the screen of those devices that were released before 2007. On later models, it is found in other modifications.
  2. If the machine is under warranty, you should not repair it at your own expense. This should be done by the masters of the branded service center.
  3. To protect yourself from fraudsters, it is better to contact a large company that repairs household appliances.

You can find out about all error codes for Samsung washing machines here.

Related videos

Why the Samsung washing machine gives out the error code LE1 (e9), the video will tell you:

Conclusion

An E9 error can indicate both minor breakdowns and serious damage. If it was not possible to eliminate the cause that provoked the appearance of the code on your own, you need to contact a specialist.

Rate the article

1 Star2 Stars3 Stars4 Stars5 stars
Loading...
Discussions

Wash

Cleaning

Scratches