Drum

foto24324-1The drum of the Samsung washing machine is a basic part of this household appliance. Without it, the operation of washing equipment is impossible.

In the article, we will consider the device and purpose of the drum of the Samsung washing machine, the main reasons for its breakdown, how to eliminate them, as well as the features of cleaning and calibration.

Device and purpose

The drum of the Samsung washing machine is one of the main parts, since it is into it that the laundry is loaded. A crosspiece with a shaft is attached to the back of the drum, which transfers the rotation from the motor to the drum.

Tank and drum should not be confused. A tub is a plastic container that surrounds the drum.

There are loopholes inside the part - these are special pads that stir the laundry during washing. Hoists can be straight or curved.

foto24324-2The surface of the part is covered with small holes - perforation. They differ depending on the model of the washing machine, but their purpose is always the same - through them the washing solution enters. However, it is they who become the cause of premature damage to things.

Samsung washing machine manufacturers are trying to solve this problem, so they have developed the unique Diamond Drum design, in which holes are in the center of pyramidal recesses, shaped like diamonds.

Thanks to this decision, the fabric under the influence of centrifugal force does not penetrate the holes and is not damaged... At the same time, the quality of washing remains at its best.

In modern appliances, not only soapy water, but also steam is supplied through the holes in the drum.

Breakdown reasons

Despite the fact that manufacturers of Samsung washing machines pay tremendous attention to the quality of their equipment, the possibility of breakage cannot be ruled out.

At the same time, a manufacturing defect, as the cause of a drum failure, is rarely observed. There are other factors that can cause a knocking or squeaking sound, or a complete stop of the centrifuge.

Does not twist

The drum can stop rotating for a number of reasons. Among them:

  • foto24324-3overloading with linen;
  • breakage or slipping of the belt;
  • wear of the motor brushes;
  • bearing wear;
  • failure of the control board;
  • broken wiring.

If reducing the load on the appliance in the form of removing some of the laundry did not help solve the problem, most likely the reason lies in a more serious breakdown. Read more in this article.

Why is it knocking?

Drum beats are not normal, but you shouldn't panic. First you need to think about what has been loaded into the device. It is possible that the unusual sound is the result of the interaction between the metal wall of the drum and any piece of clothing: plastic or metal.

If this reason is ruled out, the following issues need to be considered:

  1. There is a foreign object (coin, button, bra bone, etc.) between the tub and drum. The foreign body must be removed, which will require disassembling the washing machine.
  2. The power filter, which is attached to the back of the machine, has come off. It hits the tank, causing a knock. It is necessary to disassemble the technique and check the quality of fixing the part.
  3. Shock absorbers are out of order. If they have lost their elasticity and stretched, then having dropped to the bottom, they will begin to emit a characteristic knock on the body of the device. The drum may appear to be beating. The problem can be solved by replacing all shock absorbers.
Sometimes the knocking occurs when the washing machine is placed on an uneven surface. If a skew is detected, you need to move the device. Do not place it close to a wall or furniture.

Squeaks when washing or spinning

foto24324-4If an iron creak is heard, then the bearing is most likely to fail.

This occurs during long-term operation of the device and is a natural process. Over time, all parts wear out. To get rid of the squeak, you need to disassemble the drum, replace bearings and oil seals.

Another reason for the squeak is that parts of things that are in the wash hit the hatch cuff. Sometimes hair or hair that has strayed into a ball can lead to a squeak.

Slipping drive belt and loose shaft mount responds with a squeak... In this case, disassembly of the washing machine and elimination of the problem is required.

A common cause of squeaking is bearings that are worn out, but not completely. In the near future, it is better to replace them, or at the most inopportune moment the machine may fail.

There is water in it

If there is water in the drum and does not drain, this may be due to the following reasons:

  1. The drain filter is clogged. It can be formed by any small objects. To fix the problem, you need to clean the filter and put it back in.
  2. The pump is broken or clogged. If no dirt is found in it, the part must be replaced.
  3. The control board has malfunctioned. Sometimes a simple reboot of the device helps. It is enough to turn it off for 15 minutes and then start it up again. If that doesn't work, repair is required.

How to replace a part on a Samsung washing machine?

foto24324-5The washing machine must be disassembled to replace the drum. To begin with, twist the top panel and the parts under it.

Then go to the control panel, front wall and cuff. Be sure to remove the counterweights, disconnect the wires. Having gained access to the drum, it is removed.

It is difficult to cope with the task alone, so you need to make sure that there is an assistant nearby.

After the broken part is dismantled, a new kit is installed in its place. The procedure is carried out in the reverse order. In order not to get confused, initially you need to record the entire parsing process on a photo or video camera.

To learn how to remove the drum from the washing machine, read this article on replacing the cross - in this.

Calibration

The Samsung washing machine independently determines the weight of the items loaded into it. To make this value more accurate, you need to start the calibration mode.

This is done in several steps:

  1. Switch off the device and empty it.
  2. Press simultaneously the "Temperature" and "Delay end" button, and then "Power". The device should turn on.
  3. Press the "Start" button, this will activate the calibration mode.
  4. The drum will start to rotate clockwise and counterclockwise. The whole process takes about 3 minutes.
  5. When it stops, “End” will be displayed and the device will turn off.

After calibration, the technician is completely ready to wash.

Depending on the model, the process may differ slightly, so before starting the machine, you need to study the instructions.

Cleaning

foto24324-6One of the innovative features of modern Samsung washing machines is Eco Drum Clean. It removes odors and contaminants caused by bacteria that accumulate on the walls of the centrifuge.

To get rid of them, there is no need to buy expensive detergents. Washing the machine itself displays information that it is time to clean the drum... The owner of smart technology will only have to select the appropriate function and launch it.

If the model is outdated, then you will have to clean the drum on your own. This requires chlorine bleach and powder, which are placed directly in the centrifuge and run on a high temperature wash cycle. Read more here.

Where and for how much to buy a new one?

You can purchase a new drum from your authorized Samsung dealer. The average price of a part varies from 5,000 to 10,000 rubles. If you change it yourself, the spending will be over. Provided you contact the master, you will have to pay about 3000 - 5000 rubles, depending on the complexity of the work.

Considering that a new budget machine costs 23,000 rubles on average, buying and replacing a drum with the involvement of a specialist is not rational.

If, nevertheless, a decision is made to buy a new part, then you need to be extremely careful when placing an order. The drum must match the model of the washing machine. This is indicated in the accompanying documentation. You need to buy a drum assembly with a cross.

Master call

foto24324-7Replacing the drum costs at least 3,500 rubles, excluding the cost of the part itself. The execution time is from 1 to 3 hours. Average warranty period is 1 year.

Calling the master, you need to contact trusted specialists... It is recommended to give preference to repairmen from a large company with its own website and office in the city.

To minimize the risk of meeting scammers, first you need to study reviews about the company on the Internet. Contact masters can be found on the Web or in newspaper ads.

Conclusion

The drum of a Samsung washing machine rarely fails. If this happens, you need to try to find the cause of the breakdown and fix it yourself. When you cannot cope on your own, you should contact a specialist.

List of articles

If the drum does not spin in the Samsung washing machine, you need to determine what ...

The crosspiece of the washing machine is a part that is responsible for attaching the drum to ...

The manufacturer of the Samsung washing machine pays special attention to the quality, reliability and functionality of such ...

During operation, the washing machine comes into contact with water and detergents, is exposed to ...

Wash

Cleaning

Scratches